SECONDHAND SOUND AND LIGHTING EQUIPMENT

Description

A preloved/ex-hire Amcron VZ5000 in good condition that will be supplied after being checked, serviced and PAT tested

Specifications:

• Power Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo, 4 to 16 ohms in Bridge-Mono and 1 to 4 ohms in Parallel-mono mode. Voltage Gain to 1-kHz, 8-ohm rated output; 132:1 6% or 42 dB 1 dB gain at 0.775-volt sensitivity. 71:1 12% or 37 dB 1 dB gain at 1.4-volt sensitivity. 20:1 3% or 26 dB 0.25 dB gain at the 26-dB gain setting
• Required AC Mains: 50 or 60 Hz; 100-, 120-, 200-, 208-, 230-, 240-VAC (10%). AC Line Current, Current, voltage and frequency requirements are provided on the units back panel
• Performance Frequency Response: 0.1 dB from 20 Hz to 20 kHz at 1 watt
• Phase Response: 10 degrees from 10 Hz to 20 kHz at 1 watt.
• Signal-to-Noise Ratio,A-weighted: Better than 105 dB below rated 1-kHz power
• Total Harmonic Distortion (THD): 1-kHz rated power, 0.05% or less true THD
• Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) Less than 0.05% from rated power to 35 dB below rated power at 8 ohms
• Damping Factor: Greater than 1,000 from 10 Hz to 400 Hz
• Controlled Slew Rate: (Slew rates are limited to useful levels for ultrasonic/RF protection.) Greater than 30 volts per microsecond
• Controls Compressor: A three-position back-panel switch is used to control each channels input compressor. The "fast" setting provides an attack time of 4 milliseconds and a release time of 300 milliseconds; the "slow" setting provides an attack time of 12 milliseconds and a release time of 600 milliseconds; the "off" setting defeats output-driven compression
• Enable: A front-panel push button used to turn the amplifier on and off
• Input Ground Lift: A two-position back-panel switch located on the PIP2-FXQ used to isolate the input audio signal grounds from the AC (chassis) ground
• Level: A front-panel rotary potentiometer for each channel with 31 detents used to control the output level
• Loudspeaker Offset Integration: A two-position back-panel switch for each channel used to turn the loudspeaker protection circuitry on and off. The circuitry protects against DC, off-centre woofer cone movement, and unwanted subsonic and ultrasonic frequencies
• Sensitivity: A three-position back-panel switch for each channel used to select input sensitivity: 0.775 volts or 1.4 volts for standard 1-kHz power, or a 26 dB voltage gain
• Stereo/Mono: A three-position back-panel switch used to select Stereo, Bridge-Mono or Parallel-Mono mode
• VZ Mode: A four-position switch for each channel inside the front panel used to control the switching mode of the VZ power supplies


• Indicators Enable: An amber front-panel LED that shows the on/off status of the low-voltage power supply
• Signal/IOC: A green front-panel LED for each channel that flashes to show amplifier output. If a channels output waveform differs from its input by 0.05% or more, the indicator flashes brightly to show distortion


• ODEP: An amber front panel LED for each channel that shows thermal-dynamic energy reserve. Normally, each ODEP indicator is lit to show available reserve energy. In the rare event that a channel has no reserve, its indicator will dim in proportion to ODEP limiting
• ILoad/ILimit: A two-colour (green/red) LED for each channel that shows load current and limit current. They glow green to indicate load current flowing out the amplifier, and they turn red when maximum current is being delivered to the load
• Input/Output Input Connectors: Balanced three-pin XLR and balanced -inch(6.35-mm) TRS connectors are provided on the factory-installed PIP2-FXQ

Price: £950 each (ex carriage & vat)


Click here for more products from this seller

Delivery notes

Birmingham B7 4EE

This item is now sold